Home > Backup Exec > Backup Exec Cannot Read Barcode

Backup Exec Cannot Read Barcode

I would not recommend doing this if you are in a bad mood. Also, make sure not to select the device under the "Device Pools" section, but under "Standalone drives". All other current libraries have been qualified with the laser/laminate label Tape Library and Tape Autoloader Usage of Bar Code Label Information The following discussion assumes tapes are labeled correctly. VOX : Backup and Recovery : Backup Exec : Can backup exec be set to ignore barcodes? have a peek here

by Russell P on Sep 5, 2008 at 9:49 UTC | Data Backup 0Spice Down Next: Amazon Glacier Versioning TECHNOLOGY IN THIS DISCUSSION Avery Dennison Join the Community! Much of the early media used only six characters consisting of any combination of alpha and numeric characters. We didn't start using the LTO5 tapes with the new labels until after we upgraded. DLT Type Formats DLT tape and drive types may be divided into three versions: DLT, DLT1 and SDLT. https://vox.veritas.com/t5/Backup-Exec/Not-reading-the-barcode-in-tandberg-library/td-p/244849

Some 8 character DLT labels may be encountered for SDLT media. A threshold is determined which will separate the white areas of the label from the black areas. The very nature of this format provides verification that a valid code is present. An LTO Gen 1 cartridge that is mislabeled as an LTO Gen 2 media type may not be allowed to be inserted into an LTO Gen 1 drive.

Though, the problem you've come across might be specific to your drive. 0 Kudos Reply Contact Privacy Policy Terms & Conditions Veritas.com Support Veritas Open Exchange Login or Join Communities Information Data Recovery for Production House A production house had a FreeNAS based NAS that was crashed and non-functional and an external eSATA RAID array that was bad. The Code 39 specification allows for the addition of a checksum digit, however for most tape media a checksum digit is not used (the exception to this is the barcode label Some of the format criteria are conventions used to standardize (as much as possible) between automation and tape manufacturers.

The 2nd tape's data is from valid backups, though - we wouldn't want to overwrite media. But I would check those 2 things to make sure they line up with what you are trying to do. The label has a note indicating which side should be applied towards the hub of the tape. In general, the drive that is the target of the move must be able to perform a valid operation on that tape, either a read or a write or clean.

Note that the cleaning cartridge is defined in two places in the barcode label. The number of characters interpreted cannot be configured. Application software is also evolving to use the bar code information to track where the data cartridge is located, verify the correct media type, and confirm the identity of the exact top Do's and Don'ts of Bar Code Labels DO order labels only from HP or HP approved suppliers DON’T print labels yourself on personal printers.

i cannot erase or label the tapes on backup exec because it is greyed out Edited Aug 9, 2014 at 3:47 UTC Tags: Symantec Backup ExecReview it: (339) Reply Subscribe View https://community.spiceworks.com/topic/556807-how-can-i-solve-this-error-messages-on-backup-exec-2014 These are not printed as part of the human readable portion of the label. VOX : Backup and Recovery : Backup Exec : The library was unable to read the barcode on a ca... HP OpenView Storage Data Protector (formerly known as HP OmniBack) The application interprets all characters returned by the library.

Only the capital letters A through Z are allowed along with the numbers 0 through 9. http://cmptp.com/backup-exec/backup-exec-2012-cannot-backup-exchange-2010.html See their web site at www.colorflex.com and go to the TriOptic section. Always use the HP dual bar code label from an approved vendor for LTO type media. This was likely done intentionally to make it hard to print labels for yourself, and to encourage you to pay a rediculous fee for somebody else to print them. (like the person

At the time Data Protector determines which tape is which, Data Protector will change its knowledge of which barcode is attached to which tape. DO configure your library, where possible, to work most effectively with your labels and your software application. To ensure the tapes are only used in the correct drives you use barcode rules. Check This Out run through the wizard. * Start the services * Start the GUI - try again. 0 Jalapeno OP benben4 Aug 8, 2014 at 1:48 UTC thanks for your

An element may either be a bar (black, non-reflective) or a space (white, reflective). Label Manufacturing Processes There are two processes commonly used for manufacturing quality tape media bar code labels. Both are used in tape automation products.

Diagnostic cartridges will start with "DG(space)" followed by some sequence of characters.

And finally, the ISV software application must be configured for the bar code labels being used. Misoriented labels may be read by some libraries in some locations but not by all libraries or in all slot locations. This is different from the overwrite protection period)When we were on 2010 we had this problem all the time. Join them; it only takes a minute: Sign up Here's how it works: Anybody can ask a question Anybody can answer The best answers are voted up and rise to the

The number of characters reported to the host may only be changed using the serial port and software. Prior we used LTO5 tapes with old format labels and they were okay. 0 Kudos Reply Here is what I get from jrosenbaum Level 3 ‎08-16-2012 01:04 PM Options Mark as You might want to go to the BE installation directory and use tapeinst.exe to delete all instances of tape drives and then re-install your current tape drives. this contact form Tivoli (TSM) On UNIX platforms, TSM interprets all the characters sent by the library.

You don't really assign tapes to media sets, your jobs do that.  When you start a job, it either looks for overwritable media (new tapes, or tapes who's retention has expired) When it selects a tape out of that pool, the tape then gets assigned to the media set assigned to the job.   What I think may be happening (correct me HP SureStore models 1/20 through 10/100 and HP SureStore 1/9 models did not interpret the contents of the bar code label. However, when I performed an actual test (rotated the label 180 deg), the reader read the label correctly!

There should be a setting somewhere that dictates how data is written to tapes. The HP LTO label format contains a short bar code and a long barcode (known as the dual bar code label) as shown in Figure 1.